Make Your Own Carpet Stair Treads

A few years ago we purchased a fixer upper (and that’s putting it nicely). It actually was completely not habitable. Although most of it is finished, there are still a couple projects I’ve been wanting to get around to. One of them was to put a runner carpet down the front stairs. I priced the runner carpets and at minimum it was going to run us a few hundred dollars. If we wanted anything other than the basic run of the mill variety it was going to cost even more money. 

Not being willing to spend that much, I put my thinking cap on. My daughter and I took a trip to our local salvage store, Mardens. They have upholstery fabric for unbelievable prices. I figured there has got to be a way to use that to make my own DIY stair carpet treads. So in taking a walk around the store, I found these:

These little rugs were selling for $1.00 each. I measured them and they were the perfect length, but they were too wide. Each little rug cut in half the long way however would give me two perfect sized pieces to make my own Carpet Tread Rugs.  I then headed to the fabric department to see if they had a fabric I would like. I found this lovely fabric for $4.99 per yard. I needed three yards. I think I actually could have done with two and a half but felt safer going with three.

We then had to figure out a way to adhere the upholstery fabric to the rubber backed carpet pieces. In looking around the store my daughter and I found two things, glue and tape…crazy strong tape. I don’t know what the tape is used for but the stickiness of it makes duct tape seem like a wimp. Sorry duct tape, I still love you and was going to use you if I had not come across your bigger, stronger, super hero cousin. I know someone will ask but I have no idea what this tape is.  Mardens is a salvage store, this role had no packaging and looked just like this when we bought it. But it was huge and the price was right at $3.49. 

We purchased two bottles of this glue which said it worked on fabric at $5.99 per bottle, it was not enough glue. We ended up running to the hardware store which of course did not carry it, so we purchased a bottle of Weldbond which also said it worked on fabric. It also was $5.99 per bottle. 

First we cut all the carpet pieces we had in half. We then cut fabric pieces for each piece of rubber backed carpet. You’ll need to cut your fabric just a bit larger than your carpet piece on each side. I didn’t measure but I’d say it was about an inch or so on each side. If you decide to use this technique to make your own, you may need to center the fabric, it will depend on the overall print you choose. If possible, I would suggest choosing a fabric where centering the design will not matter. It will just be easier all around and will probably save you money as you won’t have to figure on getting the repeat in the pattern right when you measure for fabric. I chose to center my fabric left to right but not front to back.

We spread glue all over the top (the carpeted side) of the carpet pieces

We spread out the glue.

We then flipped the carpet over so the glue side was down on the backside of the fabric. Then we cut a piece of tape the length of the long side of the carpet square. Unrolling the tape proved to be the most challenging aspect of this entire project. The tape was so sticky it took tons of strength just to unroll it. 

We then gently lifted up the fabric and placed it down on the tape so the tape was just about but not quite up to the edge of the carpet piece. After we pressed on the fabric a bit to make sure it was sticking to the tape (like there was any doubt of that!), we folded it over the back side of the carpet square and pressed down to stick it. (I hope that makes sense…see the picture)

We did the same on each side. Oh, I almost forgot, we did run a bead of glue down the edge of each side right before folding the fabric and tape over the back. 

That’s basically it. For each step repeat the same process. To attach these to the stair treads we used Scotch indoor carpet tape. We ran it down each short end, in the center and along the front edge. 

This is what the set looks like on the stairs.

There are still a few details to take care of in the front hall but it’s come a long way from what it looked like the day we bought it which was this

So here are my suggestions if you should decide to make your own carpet stair treads. 

  1. Make sure the fabric you choose to use is a sturdy, heavy duty fabric such as an upholstery fabric. It also should be think enough that the glue won’t ooze through because that would make a hard stiff top on your DIY carpet stair treads, and that would feel awful if you were barefoot. 
  2. Use a sticky tape like duct tape
  3. Use plenty of glue. 

Over all this project took my daughter and I two and a half hours. Here is a break down of what we spent. 

  • Fabric $14.97
  • Glue $17.97
  • Carpet pieces $7.00
  • Tape $3.49
  • Carpet Tape $3.50
  • Total:  $46.93    I think we may have been able to do this for a bit less if we had shopped around for a larger bottle or different glue. But overall I’m happy to not have spent a few hundred. Another thing which I considered using and you may want to try is, to use burlap to cover the carpet pieces and then use some geometric shape and acrylic paints to put maybe stars or stripes or some other design on the pieces.

Let me know if you try this project. I’d love to see pictures.

Blessings,

Shelley

A .75 cent Fall Wreath

ImageToday I made a fall wreath and it cost me a whopping .75 cents. For real just .75 cents. I had found this fall garland at a yard sale for .75 cents, you can still see the price tag on it in the photo. Image

I then went off into the woods to find some vines. I pulled some bittersweet vine down out of the trees, it kills all the trees anyways so it’s good to get it down out of the them. I twisted the vine into a wreath by tucking all the ends inside each other and wrapping them around each other. Then I spray painted the wreath a nice pumpkiny orange color with paint I had left over from another project. Image

I only did this step because my front door is real dark and vine wreaths don’t show up well on it. I thought if I started with a base of orange color, any vine which showed through the leaves and things on the wreath would be orange and add to the color of the wreath instead of disappearing into the door.

Then I used my glue gun to glue on all the pieces which I had cut off of the fall garland. I added about 10 more fall leaves which I had left over from a project from last year, I think I got them in a package at the dollar store.

Then to finish it off, I added a bow made from bailing twine and some orange gingham ribbon I had left over from another project. Isn’t it wonderful when you can pretty up you world through frugality?

P1060280